Text Resize

  • -A
  • +A
  • Your rating: None (1 vote)

    A Layout Kit





    by John Yurko

    You’re ready to lay out your new shop: You have the space built, outlets in the wall, lights hung, and a wood supply ready to turn into heirloom pieces for family and friends. You have most of the machines, benches, and cabinets, with plans to buy or build what you don’t already own. You can’t wait to get the shop in working order.

    small shop


    Don’t rush into the process. The first layout is likely to remain in place until you move again. If any major workflow and dust-collection problems arise, they probably will just be tolerated. With careful planning, though, you can take advantage of the opportunity to get the layout right the first time.

    I faced this situation recently when I moved my woodshop from a spacious two-car garage below my office into a smaller 10-ft. by 20-ft. space at home. Because of this downsizing, layout was more important than ever.

    A printer is all you need
    To plan my shop, I used a modeling program on my computer, but you can use the drawings I created to plan an efficient shop on paper. Download and print the PDF below and arrange them on graph paper to create a plan view of your shop. Take the time to work out the most efficient placement of benches, cabinets, and machines, taking into account infeed and outfeed zones as well as ducting for dust collection.

    layout your shop



    You don’t have to go as far as I did, but I found it valuable to use three-dimensional modeling, which allowed me to plan my shop vertically as well—highlighting, for example, leftover wall space for mounting storage units, tools, and jigs. If you want to try the computer program, see below.

    The drawing and paper shuffling were well worth the time. Woodworking in my small shop is now efficient and enjoyable. I’ve been able to make large projects such as cabinets and a king-size bed with few compromises in workmanship or speed.



    shop pieces

    Click here to download the PDF

    What I learned
    I’ve seen many shops that are similar in size to mine, and most make serious compromises on machines yet still are choked with stuff. A typical solution is settling for bench tools or omitting some machines altogether. But I was determined not to settle, nor to lose my ability to mill rough lumber to custom sizes.

    When I began to arrange my shop on paper and on the computer screen, I realized that, in a small shop, moving wood is easier than moving machines. So I ignored the idea of setting up the space for workflow—for example, creating adjacent, sequential zones for lumber storage, rough dimensioning, final dimensioning, joinery, and so on. That workflow concept is more appropriate for larger or commercial shops.

    My first priority was to fit essential machines and fixtures in the space, including a tablesaw, miter-saw station, drill press, bandsaw, benchtop planer, benchtop disk/belt sander, compressor, router table, and workbench. My second goal was to keep them as stationary as possible.

    It was immediately apparent that the key to this design challenge would be infeed and outfeed space for each machine. These spaces can overlap, but it takes careful planning to make sure nothing gets in the way.

    Basically, I created a linear outfeed area, which includes the miter-saw station with folding wings, tablesaw with folding outfeed table, and my large router table, all in a line along the 20-ft. wall and set at the same height. The miter-saw station converts easily for use with a mortiser—with workpiece support on both sides—and it also accepts a minilathe. I even planned a location for all of the tools, blades, and jigs used with the tablesaw: on the operator side, for easy access.

    Along the opposite long wall are the planer, combination sander, drill press, bandsaw, workbench, and compressor. Each tool has dust-collection hookups and storage space to keep the relevant tools, bits, blades, and fixtures nearby. The planer is the only tool I have to roll out into the middle of the room to use, which takes about a minute, including connecting the dust-collection hose.

    Using the three-dimensional models, I also realized that even though the bandsaw’s table must be higher than the adjacent workbench, I can support large pieces with a shopmade roller support clamped in the bench’s front vise.

     

    small shop layout
    Everything within arm’s reach. Using two- and three-dimensional CAD models, Yurko crafted a bench area that packs in hand tools, air tools (and a compressor), a sharpening station. and hardware storage.

    Pros and cons of a small shop
    For all of my planning, I must admit there simply was no room in my shop for some tools. I struggled to find a place for my wide jointer and eventually decided against shoehorning it in, instead making a fixture for my router table that joints edges quite well. My scrollsaw, the bulk of my wood supply, and some storage cabinets didn’t make the cut either. These remain in a nearby room.

    In many ways it’s more enjoyable to work in a small space. Because most everything is only a couple of steps away, I’m much less fatigued after an evening of woodworking. The hours I spent planning have already saved me many hours of precious shop time.

    Use computer modeling for paper-free planning in 3-D
    You have a few options for planning your shop space: The first is simply to photocopy the two-dimensional models and use them to create a scale layout of your shop floor. You also can go to my Web site (www.yda-online.com/shopmodels.htm) and download two-dimensional images of each tool to be used either on paper or on the computer. As a third alternative, you can download the same modeling program I used, and create three-dimensional plans.

    The program is called Sketchup 4.0 (a demo version is available at www.sketchup.com, which allows 8 hours of free use). The program is easy to learn and use, even for a computer novice. If you download and learn Sketchup, feel free to go to my Web site and download my 3-D models for your own use, or use Sketchup to create your own.

    By the way, I have used Sketchup to design every piece of furniture and cabinetry I’ve built over the last few years, even working out joinery details and making color choices on the computer. And I know of many other woodworkers across the country who have discovered Sketchup and put it to good use.

    3-D shop layout shop layout
    Go three-dimensional for the ultimate plan. Creating his own three-dimensional CAD models allowed Yurko to plan vertical space as well as floor space, helping him locate spots for essential lumber, accessories, shelves, and cabinets.

    Originally published in Fine Woodworking magazine (FWW #174).


    John_Yurko

    Comments

    Comment viewing options

    Select your preferred way to display the comments and click "Save settings" to activate your changes.
    juanalesandro
    juan alesandro writes:

    I like this kit. I love it. I am thinking to make one kit like this. it seems to me easy. I will definitely try this. harley street hypnosis

    cntbill
    Bill Burkhardt writes:

    Doesn't work with my Mac Pro either, the PDF is only one page @ 207kb.

    Mac Pro dual 3 GHz, OS X 10.7.4, using Safari 5.1.7

    Rxalph
    Ralph Watson writes:

    I have Adobe 10 and the file will not open properly on my iMac

    WoodorkingBE
    Tony Maund writes:

    The link to the PDF does not appear to be working correctly on my iMac

    Login or register to post comments