Text Resize

  • -A
  • +A
  • No votes yet

    Routing Safe and Sound





    When you lose control of a router, whether totally or just a little, it's the workpiece that most often gets messed up. Now and again, you'll chip or break a bit. And if you're really unlucky, you will get hurt. Keep this in mind: Most router bits rotate at a speed in excess of 20,000 rpm. When something goes wrong—a grab, a dig, a jolt to the machine, bad things happen fast. I have had my fingernails trimmed mighty close by a dovetail bit before I knew what happened.


    Router safety is essentially a matter of controlling the router and securing the workpiece (and vice versa on the router table). Safety considerations are therefore intimately related to the quality of the cut. The safest routing technique will by and large yield the best finished surface.

    Here are some tips to help you produce the quickest, smoothest and safest cuts with a router.

    1. Some Bits Bite Back

    Not all router bits are created equal. Some are far less capable of handling the stresses of cutting wood and will break easily. Some are prone to other problems, such as burning or catching in the cut. Recognizing bits that need particular care will help you keep them from biting you and your work. 

    Long, thin bits are fragile: Thin bits with cutting-edge lengths that are more than three times longer than their diameters are easily stressed and broken. Some of the thinnest bits are milled into their shank, making them even more fragile. A 3/8-in.-dia. bit has less than 1/16-in. of steel between the flutes. Cut in 1/8-in. increments or less with these bits. 

    Trapped bits need precise guidance: Some bit designs, such as dovetail bits
    and T-slot cutters, trap the bit in the work. The slightest wavering in the cut will mess up the workpiece. These bits should be used only with jigs and fences to guide them.

    Dovetail and T-slot bits also break easily. They are designed to cut while fully  engaged in the workpiece, which is the most stressful kind of cut for any router bit. Most of the cutting is done at the ends of the flutes where their diameter is at a maximum. However, most of the stress is concentrated where the shank and the flutes meet, which is the thinnest part of the bit. To make matters worse, some of  these cutters are ground into the shank. Just take things easy, and don't force the cut. For long T-slots and sliding dovetails, first cut a groove using straight bit.

    Many other kinds of bits cut in such a way that you can't lift the router straight up and off the workpiece freely. These bits include cope-and- stick cutters, glue- and finger-joint bits, bull-nose bits and some profile bits. To be used successfully, they should be treated as trapped bits.

     Buried Bit 

    Trapped! Cutting a sliding dovetail buries the bit in the work. If the router can't be pulled up and away, the bit is trapped and needs careful guidance.

    Spiral bits can be unpredictable: Spiral up-shear and down-shear bits
    can produce impeccable surfaces. The cutting edges travel in a spiral motion
    and are always engaged in the work, unlike ordinary straight bits. Used with a hand-held router, up-shear
    bits send the chips into your face, and down shears send the chips into your
    socks. The direction of chip dispersal is opposite when used in a router table.

    Large spiral-ground down-shear bits have one nasty feature: If the bit
    catches in the work, it will push the router up and out of the cut. I almost
    lost my grip on a router with a down-shear bit that suddenly climbed up the work. Down shears are too unpredictable for this woodworker, especially on end grain. If you use them, cut very lightly, or use them in a router table with a power feed.


    Up- and down-shear bits

    A twist to the left, a twist to the right The upshear bit spins like a drill bit, with the flutes spiraling up. The downshear bit's flutes spiral down.

    2. Listen to your router whine

    Routers always seem to whine, but you should listen to them. The sound a router makes while idling should not change appreciably in the cut. If it does, you may be stressing the bit and the motor.

    It's all too easy to overwork a bit because it's difficult to estimate how much stress a particular cut will put on a bit. The volume of material you remove increases exponentially when you double the dimensions. This means that you remove 25 times more wood from a given length of a 5/8-in.-sq. rabbet than from a 1/8-in.-sq. rabbet. However, the stresses on the bit are not 25 times as great. Your best estimate will come from how it sounds in the cut. If your bit chatters, screeches or just sounds
    unhappy, then slow down the cut. If it continues to make noise, the bit may be dull.

    3. Jigs are safety devices in disguise

    Jigs secure the work and control the path of the cut, reducing the chances of error. Consequently, they are essential to the most accurate—and the safest—router cuts.

    The best jigs have a few things in common. They secure the workpiece without interfering with the path of the router. They offer a large surface for the router to run on, giving it stability. Hand jigs guide the router positively and completely through the
    cut. Avoid designing jigs that trap the workpiece between a fence and the cutter. When using an edge-guide on a router, position the bit in the fence.

    A good jig keeps the router in line. By controlling the line of cut, jigs make mistakes less likely.

    When edge trimming, part of the router hangs off the workpiece. An aftermarket offset base can greatly improve the tool's stability.

     Jigs improve safety

    A good jig keeps the router in line. By controlling the line of cut, jigs make mistakes less likely.

    4. Getting away with the climb cut

    The direction of cut has great bearing on the quality of the cut. Typically, you should cut whereby the bit is clawing at the workpiece, not rolling in the same direction (climb cutting) as the feed. But there are times when you might want to climb cut.

    If you look at a router upside down, you'll see that the bit spins counterclockwise, and when the router is on top of the workpiece, it's spinning clockwise. When the router is pushed through the cut with the bit spinning into the edge of the workpiece, it's called a climb cut. The bit can self-feed or climb along the cut, wrenching the router forward. Though risky, climb cutting produces a superior edge, without the kind of tearout anti-climb cuts produce. It should only be used when you have mastered the tool. And above all, take very light passes.

    5. Keep gravity on your side

    Bad accidents with routers do happen. I heard of a carpenter who tried to rout some molding under a countertop. He didn't secure the motor in the casting. Halfway  through the cut, the motor spun out of its casting and onto his leg. The lesson should be obvious: Keep gravity on your side. Handheld routers should always be used horizontally with the bit facing down. It can be tempting to run a router sideways
    down a board, especially if the bit is oriented to cut that way, but don't do it. Find a different bit, or make a jig that supports the piece in such a way that you rout horizontally.

     Don't run a router sideways 

    Rabbeting the wrong way. Routing sideways can be tempting but is always treacherous. If you lose your grip, the router will fall.

     Do stabilize the router when cutting 

    Rabbeting the right way. The router is easier to control when flat on the workpiece. Your hands are above the bit if you lose your grip.

    6. Start the router without wobble

    I start a router with its base casting flat on the edge of the workpiece. I find it troublesome and risky to set down an already running router on the workpiece. However, starting the router on an edge isn't completely risk-free. Some machines will jerk from the torque of the motor and possibly push the bit into the workpiece. Worse,
    starting a cut before the bit reaches full speed can break the bit. I prefer soft-start machines because they don't twist on start up.

    7. Rout Comfortably

    Routing at a standard bench height is difficult and tiring for me. I can't see what's going on easily, so I end up hunched over trying to see where the bit is. Being able to see the bit is crucial to keeping the router under control. To solve the problem, I made a special routing bench 40 in. high. It allows me to stand tall and see what I'm doing. I also make router jigs for my bench vise that stand at about the same height. I'm 6 ft. 1 in. tall, so 40 in. off the ground may not be the best height for you. Experiment to find your most comfortable routing height

     A special router bench 

    A special router bench for comfortable work. The author made this bench 40 in. high, so he doesn't have to lean over to see what he's doing.

    Photos by Strother Purdy and Scott Phillips

    This article originally appeared in the Marsh/April 1998 article of Fine Woodworking (FWW 129).


    Patrick_Warner

    Comments

    Comment viewing options

    Select your preferred way to display the comments and click "Save settings" to activate your changes.
    ocpfsd1
    ocpfsd1 ocpfsd1 writes:

    Do you want to Learn meditation in new york Light Watkins has been providing meditation course from many year in new york.Get the best meditation audio course online and best personal trainer now.

    davidalan1122
    davidalan1122 davidalan1122 writes:


    This is very educational content and written well for a change. It's nice to see that some people still understand how to write a quality post!                       linkedin advertising

    anokhi
    anokhi susan writes:

    A 3/8-in.-dia. bit has less than 1/16-in. of steel between the flutes. Cut in 1/8-in. increments or less with these bits. Modeling Agencies in Tampa

    Velen291
    Nicol Hugef writes:

    Wow! Such an amazing and helpful post this is. I really really love it. It's so good and so awesome. https://sites.google.com/site/superiorsingingmethodreviewd/

    konveksiabi
    konveksi abi writes:

    help remind you about the details that you normally forget throughout your practice by writin.

    konveksi baju sekolah, bikin baju sekolah, konveksi baju seragam, konveksi seragam sekolah murah

    konveksiabi
    konveksi abi writes:

    I will definitely dig it and personally recommend to my friends.

    konveksi baju sekolah konveksi baju sekolah tangerang konveksi seragam sekolah Konveksi kaos di Jakarta

    Commenterman
    commenter man writes:

    You have done a great job. I will definitely dig it and personally recommend to my friends. I am confident they will be benefited from this site Click here

    commentmaster
    master comment writes:

    One drawback to wiping is the very thin layer of finish it applies. Even with multiple coats  how to get free psn codes

    dalladalla
    dalladalla dalladalla writes:

    Buy Gemstones Online from Best Online Gemstone Store and Buy Loose Gemstones, Pink Tourmaline Gemstones, Pink Sapphire, Emerald Stones, Ruby Stones and Demantoid From Mystic Hue.Pass bee Media wallet

    kim89
    kim jung writes:

    thanks for the tips, this is very helpful. for me the most important is safety, so prudence and concentration are the things that should take precedence. Harga HP Nokia , Harga Nokia 108 terkini

    0ty9ohv
    Mark Silver writes:

     As the one privileged for the “mother of the groom speech” (since you are, of course, the mother of the groom), you would surely don’t want your mind to go blank during your speech presentation. So, you can do something that can help remind you about the details that you normally forget throughout your practice by writing the details on a small card, and just glance at it when you are performing the speech.

    jackjohnn
    jack smith writes:

    Only a small minority of 648-232 vce questions amateur woodworkers spray on finishes. Among the reasons are the examcollection 648-232 high initial cost of even a small-scale operation and the confuSing number of spraying options. You need an adequate source of compressed air. vce 648-232

     

     

       
    carlos6112
    Miguel Munoz writes:

    Whenever I am searching for awesome content and ideas around the net, I always this is an awesome place for that. Thanks for keeping this site alive. breaking news

    Login or register to post comments